EZLynk Tips
AFTER FLASHING THE VEHICLE
You may experience "DTC" or "Trouble Codes", If so you will need to read and clear all codes before starting the vehicle.
This is due to the EZLynk causing communication error codes during the flash process.
​
​
​
AFTER FLASHING THE TCM
We recommend after flashing the TCM, use the "Reset KAM" Procedure found on the EZLynk app under Vehicle Functions. This resets the transmissions adaptive memory and will allow the TCM to relearn the adaptive memory for the new TCM Tune installed.
If this procedure is not done you may experience erratic shifting or shift flaring.
EZLynk FAQ
I DON’T HAVE ANY ECU PROFILES AVAILABLE.
​
EZ LYNK TECHNICIAN EMAIL
You can verify that your vehicle has been lynked to a technician by viewing the ‘Technicians’ option from the ‘Vehicles’ tab.
If you have already purchased an EZ Lynk Device or Support Pack from Pure Fabrication, LLC, then you can connect to our EZ Lynk Tune Database using the following technician account:
​
​
​
​
​
THE EZ LYNK NETWORK IS NOT SHOWING UP.
​
CHECK THE AUTOAGENT™ LIGHTS
If you’re unable to see the EZ LYNK network in your device’s wifi settings please check the lights that are emitted from the unit itself. A solid green light indicates the that unit is receiving power from your vehicle. A solid blue light indicates that a wireless signal is being broadcast.
When only a green light is visible, your unit may need to be reset. You can do so by disconnecting the ethernet end of the OBD-II cable from the AutoAgent™ box. Plugging the cable back in should result in a flash of lights followed by a solid green and blue light to be emitted from the unit. When the blue light is visible, please attempt your connection again.
If a blue light is visible but the EZ LYNK network is still not visible, contact the Technical Support team for troubleshooting assistance.
​
​
​
​
I’M RECEIVING A ‘NO INTERNET’ MESSAGE.
​
CONNECTION EXPLAINED
Most mobile devices have a feature that displays a ‘No Internet Connection’ message when connecting to the EZ LYNK network. This may raise a concern at first, but the message is normal and will occur every time that you connect.
When connecting to the EZ LYNK network you are establishing means of communication with your vehicle as opposed to the internet.
​
​
​
​
I CAN’T CONNECT TO MY VEHICLE.
​
PLACE YOUR KEY IN ‘RUN’
From the moment the AutoAgent™ is plugged in, it attempts to stream data from your vehicle’s engine computer. If your ECM has not been booted prior to your communication request, you will receive a message in the app stating that you are unable to communicate with your vehicle.
By placing your vehicle’s key into the ‘Run’ position prior to establishing your connection, you are booting your ECM and allowing the app to pull accurate data.
​
​
​
​
I’M HAVING TROUBLE UPDATING MY FIRMWARE.
RECONNECT & VERIFY FW VERSION
Keeping your firmware up to date is necessary to take advantage of the innovative features that are frequently added. Depending on the previous version, it may be necessary to unplug and replug your AutoAgent™ to complete the firmware installation.
If you’ve been disconnected during a firmware update, unplug and replug your unit into the OBD-II port, connect, and open the app to verify your current firmware version. This can be viewed on the ‘About’ page from the ‘Settings’ tab of the menu.
Contact our Technical Support team if you’re unsure if you’ve updated or are having troubles.
​
​
​
​
I’M STUCK INSTALLING AT 0%.
UNPLUG & CONNECT TO THE INTERNET
When using cell data or switching networks, downloaded data can sometimes come through incomplete. This will cause your AutoAgent™ to reject the file you are trying to install and stick the app at 0%.
The best solution for this issue is to unplug the unit, connect to an internet source to fetch (the cloud button the profile you are trying install, plug the unit back in, and attempt the installation again.
Any further troubles should be directed toward our Technical Support team.
​
​
​
​
I NEED HELP WITH SOMETHING ELSE.
CONTACT US FOR SUPPORT
You can reach us by using our "Contact" Page, Please supply us with as much detail as possible with what you're needing assistance with.
Questions or troubles with the AutoAgent™, app, or vehicle communication should be directed to EZ Lynk Technical Support team.